Did you know if you have your oil changed at a non-dealer garage, they might install the wrong oil filter? Last time I had my Subaru oil changed at a non-dealer garage, they installed a wrong filter because it has the wrong bypass pressure for a Subaru. So it is important that you use a correct filter.
Most of the time going to a dealer for service is more expensive. So in this video I am showing you the easiest way to change your oil in under 20 minutes. You want it to be quick, but also safe. For a Subaru Forester, there is no need to jack up the car, the SUV is high enough, and the oil drain plug is within arm’s reach from the front. If your head is too large or your car’s clearance is too low, watch my other video on how to raise your car safely without a jack: https://youtu.be/KwJRQKDszyo
I put an oil pan in a box. The box will catch oil splashes and it also lets me adjust the pan under the car more easily. If you don’t have an oil pan, watch this video about how to make a zero cost oil pan: https://youtu.be/aPYtICiotEc?t=26
My oil filter socket fits the correct oil filter from Subaru, but it is too small for the Metrostreet filter. If you don’t have an oil filter wrench, watch my other video on how to remove the filter without purchasing a filter wrench: https://youtu.be/QPVs03aZjmc
We’ve all had the annoying moment when we just couldn’t open that jar. Lucky for you, if you watch my video, you’ll never again have to watch any other.
My ways are guaranteed to help you no matter what situation you’re in, and no matter what kind of jar it is. Whether the jar is vacuum sealed or stuck with honey or something else, I’ve got you covered! youtube
Don’t forget to subscribe for more genius videos.
You may always want to know the best way to do things. The best way depends on what is the problem. The problem could have different causes.
If you just want to purchase your opener, here is the link: Opener
If you could not open a jar, it could simply because you were turning it in the wrong direction, but assuming you didn’t make that mistake, there is only one reason why you can’t open it. That is, your force can’t overcome the resistance of the jar. For that, you may blame either the person or you may blame the jar. 🙂
If you prefer to blame the person, there are 2 possibilities. You either have weak fingers or a weak wrist/arm.
Weak fingers can’t apply sufficient force perpendicular to the surface to generate sufficient friction, thus your hand slips. To compensate for this, we can use many non-slip materials: rubber glove, leather glove, wide rubber band, balloon.
To turn the lid, you should use your arm instead of your wrist to turn the lid, because your arm is much stronger, and wrists can be easily injured.
If you feel that your weak wrist or arm is the problem, you can leverage your force by using tools with long handles. The longer the handle, the less force is needed. For example if you can extend the length of the pipe wrench, or the oil filter wrench, you will gain more power.
If you think the jar is the problem, you need to investigate the 3 possibilities of what is causing the high resistance.
The 3 causes are the vacuum seal, high friction on the threads and liner, or solidified food. You need to match the tools you have to solve each problem.
Two solutions to break the vacuum: either prying or tapping.
Prying: you may buy special tools, or you can use a beer bottle opener, a spoon, a butter knife or a screwdriver to poke around the jar’s perimeter so that you can introduce an air leak and break the vacuum.
Tapping: You may use a wooden cooking utensil to whack the top of the lid. You need to whack it hard but not so hard that you break the glass. You hope it will break the vacuum as well as unstuck the lid. You can also use the back of a knife to whack as long as you’re careful.
If a jar is vacuum sealed, then there is often a seal button, see here. If this button or the lid pops up, it means the vacuum is broken. If you have high friction on the threads, you may use a heating method. Reduce friction: Heating the metal lid will reduce the force needed because metal will expand more than glass.
The heat source could be your stove, hot water, hair dryer or cigarette lighter.
There are two common types of jar lid, one is continuous threaded where the jar and lid are both threaded in one continuous bead. It is similar to a nut and bolt. To open it, you need to turn at least 360 degree. Since the thread is long and gradual, you may potentially have a tighter seal, thus it may be harder to open it.
The second type is lug or called twist-off type where the container has multiple threads and the lid has an equal number of lugs or tabs that grip the corresponding threads. You can see a few nubs here. To open it, typically you need to turn the lid less than 90 degree. This is easier to keep clean and free from sticky product.
Sometimes a jar that has been opened before will still be tough to open if the contents are something sticky, like honey. When the lid is heated, the honey or other sticky substance should soften or melt, making it easier to twist open.
Finally, if you have a jar of honey or something sticky, you can put some plastic wrap over the thread so that it will be easy for you to open it next time.
Note: if you heat the jar, you may not heat too long because even though the vacuum has negative pressure, heating would generate vapor and thus may create positive pressure and explode.